Radyne QAM256 Instructions d'exploitation Page 59
- Page / 87
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Remote Operations QAM256 Digital Video Modulator and Upconverter
C-4 TM077 – Rev. 4.0
and recognizes that the message is a duplicate, so the associated commands within the packet
are not executed a second time. However, the response packet is again sent back to the source,
as an acknowledgment in order to preclude undesired multiple executions of the same command.
To reiterate, valid equipment responses to a message require the FSN tag in the command
packet. This serves as part of the handshake/acknowledge routine. If a valid response message
is absent, then the command is re-transmitted with the same FSN. For a repeat of the same
command involving iterative processes (such as increasing or decreasing transmit power level of
a QAM256), the FSN is incremented after each message packet. When the FSN value reaches
255, it overflows and begins again at zero. The FSN tag is a powerful tool that assures sequential
information framing, and is especially useful where commands require more than one message
packet.
The full handshake/acknowledgment involves a reversal of source and destination ID codes in the
next message frame, followed by a response code in the <OPCODE> field of the message
packet from the equipment under control.
If a command packet is sent and not received at its intended destination, a timeout condition can
occur because the packet originator does not receive a response message. On receiving devices
slaved to an M & C computer, the timeout delay parameters may be programmed into the
equipment in accordance with site requirements by Radyne Corp. prior to shipment, or altered by
qualified personnel. The FSN handshake routines must account for timeout delays and be able to
introduce them as well.
C.1.4 Global Response Operational Codes
In acknowledgment (response) packets, the operational code <OPCODE> field of the message
packet is set to 0 by the receiving devices when the message intended for the device is evaluated
as valid. The device that receives the valid message then exchanges the <SOURCE ID> with the
<DESTINATION ID>, sets the <OPCODE> to zero in order to indicate that a good message was
received, and returns the packet to the originator. This "GOOD MESSAGE" Opcode is one of
nine global responses. Global response Opcodes are common responses, issued to the M&C
computer or to another device, which can originate from and are interpreted by all Radyne
equipment in the same manner. These are summarized as follows (all Opcode values are
expressed in decimal form):
RESPONSE OPCODE DESCRIPTION
OPCODE
Good Message 0000
Invalid Size 0001
Unknown Error 0002
Invalid Control Mode
0003
Invalid Parameter 0004
Invalid Last Rate Mode 0005
Invalid Symbol Rate (Symbol Rate
Low)
0006
Invalid Symbol Rate (Symbol Rate
High)
0007
Invalid Symbol Rate (Data Rate Low) 0008
Invalid Symbol Rate (Data Rate Low) 0009
Invalid Framing 000A
Invalid Modulation 000B
Invalid Interleaver/Encoder 000D
Table 2. Response OPCODES
- Digital Video Modulator 1
- Warranty Policy 2
- Preface 4
- Table of Contents 6
- TM077 – Rev. 4.0 ix 8
- Introduction 10
- 1-2 TM077 - Rev. 4.0 11
- Installation 12
- 2.2 Removal and Assembly 13
- 2.3 Mounting Considerations 13
- TM077 – Rev. 4.0 2-3 14
- Theory of Operation 15
- 3-2 TM077 - Rev. 4.0 16
- User Interfaces 17
- 4.1.3 Numeric Keypad 18
- 4.2 Parameter Setup 19
- 4.3.1 Main Menus 20
- TM077 – Rev. 4.0 4-5 21
- 4-6 TM077 - Rev. 4.0 22
- TM077 – Rev. 4.0 4-7 23
- 4.5 Connecting the Terminal 24
- 4.6 Terminal Screens 24
- Main Menu Screen: 25
- 4-10 TM077 - Rev. 4.0 26
- TM077 – Rev. 4.0 4-11 27
- 4-12 TM077 - Rev. 4.0 28
- TM077 – Rev. 4.0 4-13 29
- 4-14 TM077 - Rev. 4.0 30
- TM077 – Rev. 4.0 4-15 31
- 4-16 TM077 - Rev. 4.0 32
- Rear Panel Interfaces 33
- 5.3 TX MON Port 34
- 5.4 TX IF Port 34
- TM077 – Rev. 4.0 5-3 35
- 5.5.1 TX PARALLEL Connector 36
- 5.5.2 REMOTE Connector 36
- 5.5.3 TX ASI Connector 36
- 5.8 Optional DVB Interface 37
- 5-6 TM077 - Rev. 4.0 38
- TM077 – Rev. 4.0 5-7 39
- 6.0 Periodic Maintenance 40
- 6-2 TM077 - Rev. 4.0 41
- Technical Specifications 42
- 7.2.1 RF Interface 43
- 7.2.2 Baseband Interface 43
- 7.2.3 Remote Interface 43
- 7.2.4 Physical 43
- TM077 – Rev. 4.0 7-3 44
- Product Options 45
- A-2 TM077 - Rev. 4.0 46
- SNMP MIB 47
- B-2 TM077 – Rev. 4.0 48
- TM077 – Rev. 4.0 B-3 49
- B-4 TM077 – Rev. 4.0 50
- TM077 – Rev. 4.0 B-5 51
- B-6 TM077 – Rev. 4.0 52
- TM077 – Rev. 4.0 B-7 53
- B-8 TM077 – Rev. 4.0 54
- TM077 – Rev. 4.0 B-9 55
- Remote Operations 56
- C.1.2 Protocol Wrapper 57
- TM077 – Rev. 4.0 C-3 58
- 02h = 00000010b 58
- C-4 TM077 – Rev. 4.0 59
- RESPONSE OPCODE DESCRIPTION 59
- Invalid Control Mode 59
- C.1.5 Collision Avoidance 60
- C.1.6 Software Compatibility 61
- C.1.8 RLLP Summary 62
- C-8 TM077 – Rev. 4.0 63
- TM077 – Rev. 4.0 C-9 64
- C-10 TM077 – Rev. 4.0 65
- TM077 – Rev. 4.0 C-11 66
- C-12 TM077 – Rev. 4.0 67
- TM077 – Rev. 4.0 C-13 68
- C-14 TM077 – Rev. 4.0 69
- TM077 – Rev. 4.0 C-15 70
- C-16 TM077 – Rev. 4.0 71
- TM077 – Rev. 4.0 C-17 72
- C-18 TM077 – Rev. 4.0 73
- TM077 – Rev. 4.0 C-19 74
- C-20 TM077 – Rev. 4.0 75
- TM077 – Rev. 4.0 C-21 76
- C-22 TM077 – Rev. 4.0 77
- TM077 – Rev. 4.0 C-23 78
- C-24 TM077 – Rev. 4.0 79
- TM077 – Rev. 4.0 C-25 80
- C-26 TM077 – Rev. 4.0 81
- Glossary 82
- G-2 TM077 – Rev. 4.0 83
- TM077 – Rev. 4.0 84
- G-4 TM077 – Rev. 4.0 85
- G-6 TM077 – Rev. 4.0 87
Produits connexes et manuels pour Modulateur Radyne QAM256
Modulateur Radyne DM240XR Spécifications
(196 pages)
(196 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.404 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels